Vehicles
Sections
130 not categorized PORSCHE 944S A ARM BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 (includes uncategorized and accessory items) 90134722303 The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex street bushing is manufactured of a more dense rubber than the original. It is a 70 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for street use. Features: improved road handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than the race 95 shore bushing please note: we recommend t...(choose a part on the right to read more) View/Change Diagram
$31.90
Make a selection 90110313101 This bushing is located in the small end of the connecting rod on the wrist pin side. Be sure to inspect and replace when refreshing the motor as worn wrist pin bushings can create piston slap which is inefficient and can cause engine damage. Sold individually. 6 necessary per car. View/Change Diagram
From $7.07
Make a selection 91133300905 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
From $273.90
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$692.05
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 91150534503 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it before metal on metal contact occurs, destroying the paint work and allowing rust to develop. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the rear bumper, we recommend replacing the bumper shock seals, part # 91150531100 shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 1 necessary per car. View/Change Diagram
From $15.50
Make a selection 91442321100 A worn bell crank bushing / bearing sleeve can cause binding. Several are commonly used on the accelerator pedal linkage. When they fail the pedal will bind up causing poor throttle response and a sticky pedal feel. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. View/Change Diagram
From $2.63
Make a selection 91434701006 Quality new replacement steering rack manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Includes: - steering joint bushings - bellows retainers - outer retaining spring - bellows - inner retaining spring - steering rack coupler disc - steering rack coupler disc lock plate sold individually. 1 necessary per car. View/Change Diagram
From $396.75
Make a selection ER2051500 High performance bushing replacement, no squeaks! Want to experience precision driving, faster lap times, improved road feel and feedback? These patented elephant racing polybronze suspension bearings set a new standard for performance, ride quality and ease-of -installation. Polybronze have a rigid bronze bearing core that does not deform. The polyurethane jacket absorbs mount irregularities while the bronze inner bearing remains true, providing a free-moving machined-fit that rides on a precision race. provided grease fittings make re-lubrication a breeze and a figure 8 groove keeps grease in place. The combination delivers zero squeaks and friction-free suspension movement. well suited to street or track, ...(choose a part on the right to read more) General Fitment911 1965-69912 1965-69 914 1970-76 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$288.00
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 91150522100 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it when servicing the bumpers. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the bumpers, we recommend replacing the shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 4 necessary per car. 2 front and 2 rear. View/Change Diagram
From $22.95
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 99737503303LA Sport (85shore)bushing for transmission mount. - reduces the movement of the transmission. - improved the handling characteristics during acceleration and curves note: model 996 Carrera only with tiptronic transmission. 500 km running-in period (light noises).
$141.90
Make a selection BBI9974010001 Features
$1,895.00
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$299.95
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$225.00
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$401.50
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$482.89
Make a selection MB1230 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$273.90
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33150046 Replace worn-out original soft rubber track rod bushings with these OEM replacements. They are made of rubber that has a 65-shore hardness value, just like the oem. They will restore the original ride comfort and are more forgiving than the clubsport (85 shore rubber). This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$60.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |